Death Penalty 21 Incriminator Audio 21" 2000W Death Penalty Series
- Incriminator Audio
- Death Penalty 21 Incriminator Audio 21" 2000W Death Penalty Series
- Allow 4-15 business days build time.
- 68.00 LBS
- Calculated at Checkout
12" Shredder Shown. Only available in that size. The 2013 Death Penalty was designed to be the ultimate ground-pounder subwoofer. Vehicles that are designed to be high powered sub-bass machines (ground-pounders) have requirements that are a bit different than both standard daily driven vehicles and SPL vehicles. They require a subwoofer that can handle extreme amounts of power for long periods of time, both thermally and mechanically, and must be able to do this time and time again.
Three years ago we introduced our Death Penalty with the S.T.A.R. (Six Tier Axis Radical Cooling) motor design with the concept of rapidly cooling the coil by pushing more air with our Air-Driven Cooling, the solution was radical, but the results were remarkable, as the coil last even longer while performing even harder. The 2013 model goal was to engineer the motor with a traditional look, but keep the S.T.A.R. design and we did just that.
The newest version of S.T.A.R. has a traditional top and bottom plate, but adds a seventh magnet wedge for even more motor force over an even larger gap. This has increased the usable X-max of the subwoofer in combination with a longer voice coil assembly. We’ve increased the motor to a 9.25” diameter for extra motor strength, as well as increased motor gap vent cooling with Air-Driven Cooling (ADC) and supplemental rear side vents. The pole vent has a dome shaped top just above the pole to allow air to be pushed out the S.T.A.R. designed side and rear vents on the cones downward stroke. Just under the dome the pole has six machined cooling vents to allow air to be pulled into the gap and the process repeats with the concept of exchanging air as fast as possible, keep fresh cooling air around the coil at all times. The motor is then covered with our custom tooled magnet boot to give the driver a uniform look.
To reduce mechanical fatigue and to maintain linear cone movement throughout the stroke a multiple layer suspension is utilized. The dual lead wires are sewn to the suspension pack in order to both eliminate noises from the lead slapping the cone, and to reduce movement of the leads which can cause them to break. The final touch is our new two-tone red and silver oversize DP skull on the front dustcap.Available in Dual 1 and Dual 2 standard as well a 12”, 15”, 18” and 21" models.
- XS – Extra Spider
- PCC – DP Coil Change - Dual 0.35, Dual 0.50, Dual 1.0, Dual 2.0
- DC – Direct Connect
- DU – Dustcap Laminated Print Upgrade
- 8 Spoke Black Cast Basket
- 3" Heavy Gauge 4 Layer Flat Aluminum Voice Coil
- Triple Black Progressive Spiders with Dual Woven Tinsel Leads
- High Pressure Kraft Fiber Reinforced Cone
- Multi-Layer Foam Surround
- 9.25" 260 Oz Double Magnet Structure with Black Nickel Finish
- 912 Oz / 62 Pound Motor Structure
- Interlocking Aluminum Spider Spacer Assembly
- CILD² - Center Interlocking Dustcap
- ADC - Air Driven Cooling
- S.T.A.R. Motor Design for Built in Motor Cooling
- Nickel Plated Push Terminals
- Wrap Around Rubber Gasket
- 2000 Watt RMS Rated
- DVC 1 ohm or 2 ohm
|12 Inch||15 Inch||18 Inch||21 Inch|
|2Ω Series||2Ω Series||2Ω Series||2Ω Series|
|480 cm²||810 cm²||1210 cm²||1620 cm²|
|.21 Cu. Ft.||.22 Cu. Ft.||.24 Cu. Ft.||.25 Cu. Ft.|
|2000 RMS||2000 RMS||2000 RMS||2000 RMS|
2 Reviews Hide Reviews Show Reviews
I have two 21s dual 2s i reconed myself and hand made 10 inch carbon dustcaps walled off each on a ct sounds 2200.1. They sound amazing tuned in a 19.5 cubic foot box at 27 hz. Hit every note and im soon to be upgrading to crescendo encore 4.5ks for each sub just need a second 350 amp alt. Would recomend them there still pounding a year later . If u order them with out the dust caps glued on my suggestion is to put carbon fiber ones on and take out the push terminals and solder in some 8 gauge leads and add some extra glue to the spider . This will be better than factory
Man, Incriminator really out did them selves when they designed this beast of a sub!!! I have it in a temporary enclosure that's 8.25 ft3 @30hz. This thing is nutz, I have a crescendo bc2000d at 1 ohm. I haven't fully powered it yet because of voltage drop. So far in 3 dayz I've had it, the rearview mirror off. This thing is so precise with kick drums and note changes. When it hits the 40hz and up it's hard to breath and is just pounding your chest. I've scared people out of my truck with this thing, every person that's sat in it has said it's the loudest thing they have ever heard!! If you want extremely loud and still sounding good, this sub was made for you!!!!! Thanks Incriminator and SSA!!!!!!